SUPD · Directive (EU) 2019/904

What the SUPD means for paper and board and how you prove it

The Single-Use Plastics Directive covers certain single-use products made wholly or partly of plastic. It sets no general minimum plastic content. National rules add product-specific limits, and these differ from market to market.

For manufacturers, brands and importers of fibre-based packaging, from paper cups to food containers.

Fibre-based cups with lids on a light background
A microscope in the laboratory

What counts as plastic

Plastic is not always visible

The SUPD refers to the polymer definition of the REACH Regulation. Natural polymers that have not been chemically modified are excluded, as are paints, inks and adhesives as such. Paper products with a separate plastic lining or coating, by contrast, can be covered. What counts is the composition and structure of the final product. The key practical point follows from this: a paper look does not prove the absence of plastic. Whether a cup or a tray falls under the directive only becomes clear when the finished product is tested.

Mono-material or coating

Not every polymer turns paper into plastic

The Commission guidelines (C/2026/4813, section 2.2.1) distinguish polymers used in the manufacture of a non-plastic material from a separate plastic coating or lining.

Schematic cross-section: paper with integrated polymers, no coating

Paper as a mono-material

Polymers integrated during papermaking, such as retention aids, binders and processing aids, do not on their own turn an otherwise plastic-free paper into a single-use plastic product. Without a plastic coating or lining, no SUPD-specific marking duty applies.

Schematic cross-section: paper with a separate plastic layer

Paper with a plastic coating

A separate layer, such as a PE barrier, is a different matter. For covered single-use items the SUPD requirements can then apply, up to marking under Article 7 and Annex Part D. Product structure and use must be assessed together with the test result.

Schematic cross-section: fibre composite with plastic layers

Fibre composite

Fibres combined with plastic layers. Here too, the structure and composition of the finished product decide whether it is covered as a single-use plastic product. A paper look does not prove the absence of plastic.

Directive (EU) 2019/904, Articles 3 and 7, recital 11, Annex Part D; Commission guidelines C/2026/4813, sections 2.1 and 2.2.1. Schematic illustrations, not measurements.

The 2027 evaluation

A case for measurable criteria

The European Commission must evaluate the SUPD by 3 July 2027. The 2026 public consultation shows recurring problems: unclear definitions, inconsistent national rules and inconsistent enforcement. 226 of 447 participants reported practical difficulties with the definitions of plastic and single-use plastic products. The consultation was voluntary and is not a representative survey. flustix took part with an official contribution on 17 March 2026 and proposes a harmonised, analytically verifiable polymer threshold, backed by independent testing and third-party certification. This is a reform proposal, not an applicable EU threshold. How a technically justified value can be derived is shown in our scientific derivation: six technical sources average 0.93 per cent polymer content, 1.03 per cent with the trace allowance.

The European flag

Europe at a glance

Five markets, different legal consequences

The percentages concern different products and legal consequences. They are not interchangeable EU-wide exemptions. Plastic contents refer to weight.

France

≤ 8%

Cup threshold

Maximum for certain single-use cups. A review in 2028 is the basis for the planned phase-out in 2030.

Italy

< 10%

Definition exemption

National exemption for plastic coatings below 10 per cent that are not a main structural component.

Belgium

≥ 10%

Ban threshold 2026

Certain cups and rigid food containers, pre-packed food excluded. From 2028, 8 per cent is planned, from 2030 3 per cent on site and 6 per cent for takeaway, each subject to an evaluation.

Sweden

> 15%

Cup ban

Single-use cups with more than 15 per cent plastic may no longer be placed on the market since 2024.

Netherlands

≤ 5%

Temporary arrangement

For paper cups and food containers for on-site consumption, with additional collection and recycling conditions. Not a general SUPD exemption.

Sources: France, decree of 24 September 2021, Article 2. Italy, Legislative Decree 196/2021, Article 3(1)(a). Belgium, Royal Decree of 25 May 2024, Articles 3, 7 and 9. Sweden, Naturvårdsverket, guidance on single-use plastics. Netherlands, ILT, single-use plastics, enforcement arrangement 2026.

Plastic granulate and sample tubes

The evidence gap

What is actually in the finished product?

Supplier declarations and material data sheets describe the input materials. They do not always fully prove the plastic content of the finished product. Independent product testing links the material information to a documented result and a market-specific regulatory assessment. In the flustix LESS PLASTICS programme, the final product is tested in the laboratory and assessed by an independent certification partner. The certification proves a plastic content of at most 5 per cent and thus covers relevant criteria of the PPWR 95/5 rule, for example for exemptions from certain packaging bans from 2030. It provides evidence; it does not replace a full legal compliance review.

Three questions before testing

How to get to robust evidence

01

Identify

Which relevant polymers does the product contain, as a coating, a lining or in the material itself?

02

Assess

Which rules apply to exactly this product and this target market? Test scope, sampling and target market are agreed before testing.

03

Quantify

How much plastic does the finished product contain? The result enters the public certificate database with a licence number.

Value for companies

Evidence for different markets

Uniform technical evidence can reduce queries and make decisions for several target markets easier. Financial benefits depend on the respective tax or EPR system and the evidence it recognises.

Documentation

Handle customer enquiries and internal assessments more easily.

Market access

Support product classification and procurement decisions in EU markets.

Savings potential

Prove material or recycling criteria for taxes and EPR fees.

Plastic tax: financial benefits through certified evidence

The 95/5 approach is gaining importance in packaging law. Where a 5 per cent plastic limit applies, flustix provides independent quantitative evidence for the corresponding classification.

United Kingdom: Packaging EPR (Amendment) Regulations 2025, Reg. 4(2). EPR: Waste Framework Directive 2008/98/EC as amended, Article 8a(4)(b) on fee modulation.

An aircraft above stacked shipping containers

Free EmpCo Claim Check

Do your environmental claims hold up under the new rules?

From 27 September 2026, EmpCo brings markedly stricter requirements for environmental claims and sustainability labels: claims must be specific, verifiable and substantiated. Send us up to five of your claims and we will set out which of them already hold, which should be made more precise and where independent evidence is advisable or required. You receive a written assessment as a PDF within two to three working days. Free of charge and without obligation.

Packaged products whose environmental claims are being checked

Do you know the plastic content of your product?

One product, several markets, one basis of evidence

Tell us the composition, intended use and target markets. We will determine the right testing and certification route.